Container Glossary 集装箱专业英语词汇表

集装箱专业英语词汇表

中 文 英 文 中 文 英 文
一. 集装箱的种类
集装箱 Container 开顶集装箱 Open top container
干货集装箱 Dry cargo container 超高集装箱 HC (high cube) container
冷藏集装箱 Reefer container 标准集装箱 GP (general cargo) container
折叠集装箱 Folded container 尺寸类型: 20', 20'HC, 40', 40'HC, 45', 48'及53'等 Type & size: 20', 20'HC, 40', 40'HC, 45', 48' & 53', etc.
       
       
二. 集装箱相关组织及标记
国际标准化协会 The International Organization for Standardization  (I.S.O.)
集装箱国际安全公约 The International Convention for Safe Containers 
Container Safety Convention  (C.S.C.)
国际货运海关公约 The Customs Convention on the International Transport of Goods
Transport International Routier (T.I.R.)
国际铁路联盟公约 The International Union of Railway 
Union International Chemin (U.I.C.)  如:ic/33,33代表中国
澳洲卫生部木材处理证书 Treatment Certificate of Timber in accordance with the requirement of Australia Department of Health. 
Australian Requirements for Treatment of Container Timber  (T.C.T.)
       
       
三. 关于集装箱物理特性的名词
1. 尺寸 Dimension
外部长度 External length 开门宽度 Door opening width
外部宽度 External width 开门高度 Door opening height
外部高度 External height 公差 Tolerance
内部长度 Internal length 对角线长度 Diagonal length
内部宽度 Internal width    
内部高度 Internal height    
       
2. 重量 Rating
总重 Max gross weight 堆码试验载荷 Stacking test load
自重 Tare weight 地板强度 Floor strength
最大载荷 Max payload 公斤 KG
       
3. 容积 Capacity
内容积 Inside cubic capacity    
Pound (LB)    
       
       
四. 集装箱的主要结构 (五大部分)
1. 前端 Front end
前端上梁 Front header  拉筋 Lashing rod
前端楣板 Front header cap 角件 Corner casting
前楣加强板 Front header web 小封板 Closing plate
前顶加强板 Front roof corner gusset 前底角钢 Bottom support angle
前端下梁 Front sill 前底角支承板 Corner floor support
前下梁加强板 Front sill web 前底角封板 Bottom cover plate
前墙板 Front panel 前端防碰槽钢 Front channel section
前角柱 Front corner post 前防槽封板 Front channel section cover plate
       
2. 后端 Rear end
门楣 Door header lower 门锁杆 Locking device
门楣板 Door header cap 锁杆托架 (大、小) Bearing bracket (large & small)
门楣加强板 Door header web 衬套 Short split bush
后顶加强板 Rear roof corner gusset 胶垫 Shim
门槛 Door sill 锁头 Gear cam
门槛加强板 Door sill web 锁座 Gear cam keeper
后防碰槽钢 Rear channel section 定位环 Anti-rack ring
后防槽封板 Rear channel section cover plate 把手 Lock handle
内角柱 Rear post inner 把手插孔 Handle hub
后角柱 Rear post outer 锁牌 Catch
拉筋 Lashing rod    
角件 Corner casting 门铰链 Hinge
门板 Door panel 铰链销 Hinge pin
门横梁 Horizontal  door frame 门耳朵 Hinge butt
门竖梁 Vertical door frame 平垫 Plain washer
门梁封板 Door frame cover plate 门封 Door gasket
门搭扣 Door keeper 门封压条 Gasket retainer
门绳 / 尼龙绳 Door holder / Nylon    
       
3. 底架 Base
底侧梁 Bottom side rail 绳勾 Lashing ring
底侧梁加强板 Gusset plate 门勾 Door hook
底横梁 Crossmember    
叉槽 Fork pocket 鹅颈槽 Gooseneck tunnel
叉槽加强板 Fork pocket web 鹅颈槽主横梁 Tunnel bolster
叉槽盖板 Fork pocket plate 鹅颈槽侧梁 Tunnel side rail
叉槽底板 Fork pocket bottom plate 鹅颈槽背梁 Tunnel bow
叉槽支承角钢 Fork pocket support angle 鹅颈槽盖板 Tunnel plate
叉槽侧梁 Fork pocket side rail 短底横梁 Outrigger
地板中梁 Floor center rail    
地板支承角钢 Floor support angle    
地板 Floor    
       
4. 顶 Roof
顶板 Roof panel    
顶侧梁 Top side rail    
       
5. 侧 Side
边波板 Side wall outer 通风器 Ventilator
有孔边波板 Side wall outer (hole)    
波纹板 (大) Side wall inner (large)    
波纹板 (小) Side wall inner (small)    
       
       
五. 集装箱零附件
1. 商标 Marking
铭牌 Consolidated plate 尺寸及类型代码标 Size and type code
箱主标 Owner's logo 重量标 Weight decal
箱主系列号 Owner's serial number 高度标 Height decal
制造商标 Manufacturer's logo U.I.C标 U.I.C decal
制造商系列号 Manufacturer's serial number 钢材标 Corten steel mark
船检标 Classification decal 油漆标 Paint specification decal
       
2. 油漆 Paint
底漆 Primer 环氧漆 Epoxy primer
中间漆 Middle primer 环氧富锌底漆 Epoxy zinc rich primer
面漆 Top coat 氯化橡胶漆 Chlorinated rubber paint
沥青漆 Bitumen wax / Underseal 天那水 Thinner
地板清漆 Varnish 固化剂 Hardener
       
3. 其它 Others
标准件 Standard parts 铭牌拉铆钉 Blind rivet
螺栓 Bolt 门封拉铆钉 Blind rivet
螺母 Nut 地板自攻螺钉 Self-taping screw
弹簧垫圈 Spring washer 密封胶 Sealant
通风器铆钉 POP rivet 铁胶(金属胶) Metal cement
防盗铆钉 Huck bolt    
       
       
六. 相关设备及工具名称
平板打砂机 Shot-blasting machine 油压千斤顶 Hydraulic jack
部件打砂机 Parts shotting machine 钻头 Drill bit
罗拉机 Rolling machine 气动手钻 Air drill machine
冲床 Punching machine 桥式起重机 Over head crane
压床 Pressing machine 空气压缩机 Compressor
剪床 Clipping machine 气缸 Air cylinder
校平机 Flatting machine 锤子 Hammer
自动焊机 Auto-welding machine 凿子 Chisel
手动焊机 Manual-welding machine 气动扳手 Air spanner
打砂间 Shotting room 防毒面具 Gas mask
油漆房 Painting room 手套 Glove
流平房 Flash-off room 集装箱吊车 Container crane
烘干房 Drying room / Oven 叉车 Lift truck
喷漆机 / 枪 Painting pump / gun 堆高车 Stack truck
砂轮机 Grinding machine    
手电钻 Electric drill    
割枪 Flame torch        
       
       
七. 主要质量检验名词
材料 Material 成型差 Poor shape
钢板 Steel 打磨 Grinding
麻坑 Pit 飞溅 Spatter
生锈 Rusty 熔坑 Crater
热镀锌材料 Hot dipping zinc galvanized material 焊瘤 Overlap
    咬边 Undercut
打砂 Blasting 烧穿 Burnt-through
钢砂 Abrasive grit   漏焊 Miswelds
钢丝头 Wire 气孔 Blow hole
清洁度 Cleanliness    
密度 Density 油漆 Paint
粗糙度 Roughness 打影 Holiday
瑞典喷砂标准 Swedish Standard SA 2.5 流挂 Sagging
膜厚 Profile / Film thickness 污染 Contamination
胶带试验 Tape test 流平 Flash off
    预涂 Touch up
焊接 Welding 干膜厚度 Dry Film Thickness
焊缝 Welding seam 湿膜厚度 Wet Film Thickness
满焊 Full welding 针孔 Pin hole
花焊 Step welding /
Stitch welding
橙皮 Orange peel
点焊 Tacks welding    
自动拼焊 Auto butt welding 平直度 Alignment
渗透 Penetration 裂纹 Crack
扭曲 Twist 弯曲 Bent
错边 Uneven 间隙 Gap
波浪 Wave 修理 Repair

logo

Gateway Container International Limited, a subsidary of Gateway Logistics, specialized in container trading, and container one way leasing . The main service area is Eurasia.

Get In Touch

RM.419-421, Tianda Business Centre, No.203, Moling Road, Jing'an District, Shanghai, China. P.C.:200070

+86(21) 6393-1256

  sales@gatewaycontainer.com

 www.gatewaycontainer.com

Join Our Community

Sign up to receive email for the latest information.